Compiling the iMote2 kernel

From University of Washington - Ubicomp Research Page
Revision as of 03:42, 23 January 2007 by Jonathan Lester (talk | contribs)
Jump to navigationJump to search

Downloads

Build Tools

    Title Link Description
    iMote2 Toolchain updated Mainstone version Use either the updated Mainstone version with an updated version of binutils. The handheld.org toolchain is similar but won't build the kernel.

Needed Files


Getting Started

If you simply want to build the kernel, the easiest way is to just run the typical build script at the bottom of the page, here.


Typical Build

  • MSB2 Build
  • Windows RNDIS Gadget Driver
  • Wifi Module
  • No Standard UART console

Note, make sure the PATH is correct for your compiler and that you run this under tcsh.
Note, that "rm -rf /something" is used in this file so use it at your own risk (especially since some parts like mounting and loading modules must be run as root). It is recommended that you past each line by itself (or in small groups) to avoid any problems and to ensure a successful build <bash>

  1. !/bin/tcsh

setenv PATH "/usr/local/arm/3.4.3_binutils/bin/:${PATH}" setenv ARCH arm setenv CROSS_COMPILE arm-linux- wget http://sifl.cs.washington.edu/files/imote2/mirrors/platformX/SG2Release-1_0.tgz wget http://sifl.cs.washington.edu/files/imote2/patches/msb2_patches.tgz wget http://sifl.cs.washington.edu/files/imote2/mirrors/kernel/linux-2.6.14.tar.gz wget http://sifl.cs.washington.edu/files/imote2/images/current/fs.jffs2 wget http://sifl.cs.washington.edu/files/imote2/mirrors/zd1211/zd1211-driver-r83.tgz wget http://sifl.cs.washington.edu/files/imote2/patches/linux-2.6.14_advancedRouter.patch

setenv PLATX_NOCONSOLE 1

tar zxf linux-2.6.14.tar.gz tar zxf SG2Release-1_0.tgz tar zxf msb2_patches.tgz tar zxf zd1211-driver-r83.tgz

echo "--------------------" echo "Building and compiling Kernel" cd linux-2.6.14 echo "Applying SG2 Patches" patch -p1 < ../SG2Release-1_0/src/patch-2.6.14-sg2-10

echo "Applying MSB2 Patches and kernel config" patch -p1 < ../msp-linux-2.6.14-pxa-mmc.patch patch -p1 < ../msp-linux-2.6.14-uart.patch patch -p1 < ../msp-linux-2.6.14-sd-detect.patch cp ../msp-linux-2.6.14-config ./.config

echo "Applying Windows RNDIS Patches" patch -p1 < ../msp-linux-2.6.14-winXP-rndis.patch

if($PLATX_NOCONSOLE) echo "No Console patch 1 of 3 (kernel)" if($PLATX_NOCONSOLE) patch -p1 < ../msp-linux-2.6.14-noConsole_boot.patch if($PLATX_NOCONSOLE) patch -p1 < ../msp-linux-2.6.14-noConsole_config.patch

echo "Building kernel" setenv ARCH arm setenv CROSS_COMPILE arm-linux- sed -e 's;export PATH;#export PATH;g' -e 's;export CROSS_COMPILE=;#export CROSS_COMPILE=;g' -e 's;test:;#test:;g' Makefile.platx -i sed -e 's;echo zImage is ${ZIMAGE};#echo zImage is ${ZIMAGE};g' -e 's;${IMAGE}:: force;#${IMAGE}:: force;g' Makefile.platx -i sed -e 's;@scripts/platx_config;#@scripts/platx_config;g' Makefile.platx -i make oldconfig make zImage make modules make modules_install

echo "Copying zImage" cd .. mkdir images cd images cp ../linux-2.6.14/arch/arm/boot/zImage ./ cd ..


echo "--------------------" echo "Building Zydas driver" cd zd1211-driver-r83 sed -e 's;MODPATH := /lib/modules/$(VERSION);MODPATH := ../linux-2.6.14/modules/lib/modules/2.6.14_r1.0;g' Makefile -i sed -e 's;KERNEL_SOURCE=$(MODPATH)/source;KERNEL_SOURCE=$../linux-2.6.14;g' Makefile -i sed -e "s;CC=gcc;CC=${CROSS_COMPILE}gcc;g" -e "s;CPP=g++;CPP=${CROSS_COMPILE}g++;g" -e "s;LD=ld;LD=${CROSS_COMPILE}ld;g" Makefile -i sed -e 's;$(MODPATH)/net;$(MODPATH)/kernel/drivers/net;g' Makefile -i sed -e 's;depmod -a $(VERSION);depmod -F ../linux-2.6.14/System.map -b ../linux-2.6.14/modules -a 2.6.14_r1.0;g' Makefile -i sed -e 's;gcc -o apdbg apdbg.c;$(CC) -o apdbg apdbg.c;g' Makefile -i sed -e 's;cp ./apdbg /sbin/apdbg;#cp ./apdbg /sbin/apdbg;g' Makefile -i make make install cd ..


echo "--------------------" echo "Mounting Filesystem and installing kernel modules" cd images mkdir /mnt/jffs2Image losetup /dev/loop/0 ../fs.jffs2 mknod /dev/mtdblock0 b 31 0 modprobe blkmtd device=/dev/loop/0 mount -t jffs2 /dev/mtdblock0 /mnt/jffs2Image cd .. echo "Removing all old modules from JFFS2 Image" cd images rm -rf /mnt/jffs2Image/lib/modules/* echo "Copying new modules to JFFS2 Image" cp -a ../linux-2.6.14/modules/lib/modules/2.6.14_r1.0/ /mnt/jffs2Image/lib/modules/ echo "Copying Zydas utilities to /sbin" cp ../zd1211-driver-r83/apdbg /mnt/jffs2Image/sbin echo "Saving a copy of the .config to the filesystem" cat ../linux-2.6.14/.config | grep -v # | sed '/^$/d' > /mnt/jffs2Image/lib/modules/kernel.config if($PLATX_NOCONSOLE) echo "No Console patch 2 of 3 (inittab on fs)" if($PLATX_NOCONSOLE) patch /mnt/jffs2Image/etc/inittab ../noConsole-inittab.patch

echo "Unmounting image" sync umount /mnt/jffs2Image modprobe --remove blkmtd losetup -d /dev/loop/0 rm fs.jffs2 cp ../fs.jffs2 ./ cd ..


echo "--------------------" echo "Building blob bootloader" cd SG2Release-1_0/src tar zxf blob-px2-10.tgz cd blob-px2/src if($PLATX_NOCONSOLE) echo "No Console patch 3 of 3 (patching blob)" if($PLATX_NOCONSOLE) patch -p1 < ../../../../Blob_noconsole.patch cd blob sed -e 's/blob_status.boot_delay = 10;/blob_status.boot_delay = 0;/g' main.c -i patch -p1 < ../../../../../Blob_imote2_setGPIO10_outputHigh_forBT_and_SD.patch patch -p1 < ../../../../../Blob_imote2_setGPIO57_outputHigh_forLSB.patch patch -p1 < ../../../../../Blob_sg2_32kHzOutputDisable.patch cd ../../ make -f Makefile.cvs make -f Makefile.cvs ln -s ../../../linux-2.6.14 linux ./configure --host=arm-linux --with-board=stargate2 \ 

   --with-linux-prefix=$PWD/linux \
   --enable-xlli --enable-network --enable-xmodem

make cp src/blob/blob ../../../images/ cd ../../../</bash>


Steps

Extracting all the Images

    Assuming you placed the platformX release, patches, and kernel in the same directory you could extract them all using the following commands: <bash>tar zxf linux-2.6.14.tar.gz tar zxf SG2Release-1_0.tgz tar zxf msb2_patches.tgz</bash>

Patch the kernel

    First we apply the SG2 release patches then we apply our MSB2 patches: <bash>cd linux-2.6.14 echo "Applying SG2 Patches" patch -p1 < ../SG2Release-1_0/src/patch-2.6.14-sg2-10 echo "Applying MSB2 Patches" patch -p1 < ../msp-linux-2.6.14-pxa-mmc.patch patch -p1 < ../msp-linux-2.6.14-uart.patch patch -p1 < ../msp-linux-2.6.14-sd-detect.patch</bash>

Configure the kernel

    At this point you can either use the normal SG2 configuration or apply the msb2 standard configuration. Be sure to add your toolchain to your path, if you've installed it in /usr/local/arm/3.4.3_binutils you could do something like this: <bash>export PATH=/usr/local/arm/3.4.3_binutils/bin/:$PATH export ARCH=arm export CROSS_COMPILE=arm-linux-</bash>

    SG2 Configuration

      The base SG2 configuration, by itself its typically not too useful. <bash>export ARCH=arm export CROSS_COMPILE=arm-linux- make stargate2_defconfig make oldconfig</bash>

    MSB2 Configuration

      The default MSB2 configuration, most builds will want to use this ontop of the SG2 base. <bash>export ARCH=arm export CROSS_COMPILE=arm-linux- cp ../msp-linux-2.6.14-config ./.config make oldconfig</bash>

    RNDIS (Windows XP) Ethernet Gadget Configuration

      If you'd like to be able to connect the iMote2 to a Windows XP host instead of a linux host you can use the RNDIS patch to add Windows XP support to the kernel. Download the patch from here to your build directory. Note, that this patch currently compiles support into the kernel and not as a module. <bash>export ARCH=arm export CROSS_COMPILE=arm-linux- cp ../msp-linux-2.6.14-config ./.config patch -p1 < ../msp-linux-2.6.14-winXP-rndis.patch make oldconfig</bash> Next you will need to do a make menuconfig (after setting up the ARCH/CROSS_COMPILE/path) and select:
      • Device Drivers
        • USB Support
          • USB GadgetSupport
            • Support for USB Gadgets (compile into the kernel)
            • USB Gadget Drivers (compile into the kernel)
            • Make sure 'Ethernet Gadget (with CDC Ethernet Support)' is selected
            • Select 'RNDIS support (EXPERIMENTAL)'
      Then exit out and save your kernel configuration.

    Configuring the kernel to use multiple Internet connections

      In order for the iMote2 to selectively use multiple Internet connections simultaneously, you must enable "policy routing" in the kernel: <bash>make menuconfig</bash> Select the following:
      • Networking
        • Networking options
          • IP: Advanced router
          • IP: Policy routing (will not appear unless "Advanced router" is set)
      You can also use the following patch here.

Compile the kernel

    You can then build the kernel as you normally would or perform any additional steps you want to before building. Note that if you are using the Mainstone tools instead of a 3.4.1 toolchain installed in /usr/local/arm/3.4.1 you will need to edit Makefile.platx and comment out the export lines at the top. <bash>...
    1. export ARCH=arm
    2. export CROSS_COMPILE=/usr/local/arm/3.4.1/bin/arm-linux-
    3. export PATH:=${PATH}:/usr/local/arm/3.4.1/bin/
    ... </bash> You can also remove the platx_config to get rid of an annoying error message in the SG2_1.0 release: <bash>${IMAGE}:: force @scripts/platx_config</bash> Now you're ready to build the kernel: <bash>mkdir ../kernel make zImage make modules make modules_install cp arch/arm/boot/zImage ../kernel/ cp -a modules/lib/modules/2.6.14_r1.0/ ../kernel/ </bash> Note you should remove the '../kernel' directory each time you do this to avoid getting a stale copy; however, I'm not about to place rm -rf commands in things people will paste arbitrarily

Building the zd1211(b) wireless driver

    While the newest versions of Linux support the zd1211(b) out-of-the-box, the kernel used on the iMote2 does not. Therefore, you must download and compile the driver separately:
    • Obtain and extract the latest version from [1]. As of the time of this edit, this was r83. You can do this in one step with: <bash>wget http://zd1211.ath.cx/download/zd1211-driver-r83.tgz -O - | tar xvzf -</bash>
    • cd to the newly-created directory.
    • Edit the Makefile, and change the MODPATH (on line 13) to point at your modules/lib/modules/2.6.14_r1.0/ directory.
    • Compile and install:
    <bash>make make install</bash>

Putting it all together

    In order to combine the various steps together to create a ready to use kernel images/modules you need to complete the previous steps, copy the kernel image to someplace convenient, and copy the kernel images to the filesystem. See the script at the bottom of this page for instructions on installing the kernel modules and building the bootloader.


Flashing the kernel

    You will need to specify the platform (SG2/Intel Mote2) and JTAG cable that you are using (Intel(R) JTAG Cable/JTAG CPU) to XFlash. The following assumes you are programming an Intel Mote2 with a Macraigor Raven JTAG: 
    xflash -p intelmote2 -tt "JTAG CPU" blob     -offset 0x00000000
xflash -p intelmote2 -tt "JTAG CPU" zImage   -offset 0x00040000
xflash -p intelmote2 -tt "JTAG CPU" fs.jffs2 -offset 0x00240000

    And the following assumes you are programming an Intel Mote2 with an Intel JTAG 

    xflash -p intelmote2 -tt "Intel(R) JTAG Cable" blob     -offset 0x00000000
xflash -p intelmote2 -tt "Intel(R) JTAG Cable" zImage   -offset 0x00040000
xflash -p intelmote2 -tt "Intel(R) JTAG Cable" fs.jffs2 -offset 0x00240000
Retrieved from "https://ubi.cs.washington.edu/wiki/index.php?title=Compiling_the_iMote2_kernel&oldid=1582"